Ad_Feed

Friday, October 3, 2014

How do you reset the circuit protection on Yamaha RX-v373?

Yamaha RX-V373 AV receiver's protection circuity is activated when there is fluctuation in power three (3) consecutive times. This protection mode disables the capability to "turn on" the device.

To disable this:

Hold "Info + Tone Control + Straight" for at least five seconds, while still holding, press the "Power" button.

Manually reboot the AVR for normal operation.
Posted by at

38 comments:

  1. UnknownJuly 1, 2016 at 1:41 AM

    I did this, got a click, but nothing else?

    ReplyDelete
  2. UnknownJuly 1, 2016 at 1:41 AM

    I did this, got a click, but nothing else?

    ReplyDelete
  3. UnknownJuly 12, 2016 at 9:38 AM

    I got same problem

    ReplyDelete
  4. UnknownJuly 12, 2016 at 9:38 AM

    This comment has been removed by the author.

    ReplyDelete
  5. DaniloJuly 23, 2016 at 6:08 PM

    For RX-V377, simply hold INFO + TONE CONTROL for 5 seconds and while still pressed click POWER (do not hold it).

    ReplyDelete
  6. UnknownDecember 21, 2016 at 9:05 PM

    Hi all. I have this issue on a 373. I have tried both steps and all I get is a click. Any suggestions?

    ReplyDelete
  7. Paddy GFebruary 18, 2017 at 10:34 PM

    any updates to this thread? I tried all of the above on my V375 but I got nothing (not even a click).

    ReplyDelete
    Replies
    1. TedApril 26, 2017 at 3:33 AM

      same issue

      Delete
    2. Tech-OpensourceOctober 13, 2017 at 1:50 PM

      I did this on a V373, and it worked. I cant say for a V375.

      However, there is a comment for V377. You could try it. "For RX-V377, simply hold INFO + TONE CONTROL for 5 seconds and while still pressed click POWER (do not hold it)"

      Delete
  8. vcm007August 16, 2017 at 12:09 PM

    I did the same.
    It keeps on verifying
    no solution.

    ReplyDelete
    Replies
    1. Tech-OpensourceOctober 13, 2017 at 1:51 PM

      Since its verifying, then it came on. It best to manually reboot the AVR.

      Delete
  9. UnknownNovember 9, 2017 at 3:32 AM

    What does "manually reboot AVR" mean?

    ReplyDelete
  10. UnknownDecember 20, 2017 at 2:52 AM

    it didn't work on my avr

    ReplyDelete
  11. UnknownJanuary 9, 2018 at 4:05 PM

    Works on the 377

    ReplyDelete
  12. UnknownJanuary 9, 2018 at 4:07 PM

    Am glad I came across this. Had packed my RX 377 and was taking to technicians.

    ReplyDelete
  13. ElectromindMarch 22, 2018 at 9:09 PM

    Rxv379

    ReplyDelete
  14. ElectromindMarch 22, 2018 at 9:11 PM

    Work for my rxv379. Hold: info, tone + power.

    ReplyDelete
  15. Rodrigo PerezMay 17, 2018 at 11:52 PM

    great ¡¡¡¡¡ Do It¡¡¡¡ best regard from Chile

    ReplyDelete
  16. UnknownMay 26, 2018 at 2:08 AM

    Worked for me on my V-373 AFTER i unplugged it 1st then plugged back in. Info..Tone Control...Straight..... then Power button.

    ReplyDelete
  17. UnknownMay 29, 2018 at 4:56 PM

    Anyone know the correct buttons to push for the same problem on a Yamaha R-N303?

    ReplyDelete
  18. UnknownAugust 16, 2018 at 5:06 PM

    does not work on Yamaha RX-v373 just the click, what can I do?
    How to do a manual reset?

    ReplyDelete
  19. FlowJanuary 24, 2019 at 12:27 AM

    I have the same problem with my brand new Y R-N303. Frustrating...

    ReplyDelete
  20. UnknownApril 17, 2019 at 9:35 PM

    Worked fine for my RX-V373, though I did unplug it first, and then plugged it back in before hitting Info+Tone Control+Straight for ~10seconds, then Power.

    ReplyDelete
  21. LarkinaSeptember 30, 2019 at 11:21 PM

    After performing the circuit-protector reset. What is this bypass message that comes up on the avr screen?

    ReplyDelete
  22. UnknownNovember 9, 2019 at 5:56 AM

    Can't get it to work, just a click .. any suggestions?

    ReplyDelete
  23. UnknownDecember 1, 2019 at 4:35 PM

    worked on my outdoor v677. info + tone control (must hold for at least 5-10 seconds) then click the power button. IT WILL NOT WORK IF YOU DON'T HOLD THE INFO AND TONE DOWN FIRST!

    ReplyDelete
  24. UnknownFebruary 7, 2020 at 6:31 AM

    Thanks folks- I have a RX-V385 and it worked just fine. Had to hold the combination of buttons down for 10+ seconds, then hit power.

    ReplyDelete
  25. UnknownFebruary 10, 2020 at 11:32 PM

    Yamaha V 583 ds through?

    ReplyDelete
  26. UnknownFebruary 10, 2020 at 11:33 PM

    Main wont come on?

    ReplyDelete
  27. UnknownApril 12, 2020 at 12:55 AM

    Tried all possible combination of buttons on my V383 and none of them worked. Any suggestions?

    ReplyDelete
  28. UnknownApril 12, 2020 at 12:56 AM

    Did not work on my V383. Any suggestions?

    ReplyDelete
  29. UnknownMay 7, 2020 at 12:32 PM

    it worked for me but what do i do next ?

    ReplyDelete
  30. JavierJuly 7, 2020 at 8:31 PM

    Gracias a vuestros comentarios, puede desbloquear mi RX-V379 que, por razones desconocidas, se puso en I PROTECT. Pulsé tone+info por más de 5 sec, luego power y se puso en modo de alguna configuración desconocida. Apagué y volví a encender y funcionó. Lo estoy probando... Saludos desde Argentina

    ReplyDelete
  31. JavierAugust 30, 2020 at 2:15 PM

    Estimados. Vuelvo sobre el tema. El procedimiento que describí antes, solo posibilitó que el amplificador funcione por unos minutos y vuelva a ponerse en protección. Desbloquear el equipo tal como lo hice, podría haber provocado mayores daños. En realidad, se puso en modo de protección porque estaba en corto circuito la etapa de salida, debido a un accidente: al encender una laptop con Bluetooth activado, el ampli cambió de fuente (a Bluetooth) y quienes estaban mirando una película, que se escuchaba por el Yamaha, ante la ausencia de sonido, subieron el volumen al máximo.
    Recomiendo que limiten al volumen máximo del amplificador y que NO LO DESBLOQUEEN. Deben llevarlo al servicio técnico.
    Saludos!!

    ReplyDelete
  32. UnknownOctober 13, 2020 at 1:25 PM

    Worked for me on a RX-V677. Had the blinking red light. Now works perfectly. Held down info+tone control + straight, hit power on button and it lit up! Thanks.

    ReplyDelete
  33. UnknownDecember 21, 2020 at 6:56 PM

    Did not work for me on RX-V479 no matter how long I held down the buttons. However, the display did briefly flash "NO PROTECT" and then 3 error codes one after another: E4, EN, SC

    ReplyDelete
  34. BlaznXJuly 12, 2021 at 6:17 PM

    This works for the RX-V477 (info + control @ 5 seconds then press power button and release all buttons at the same time)... but after resetting and turning it back on, it goes back into protection mode after the three triesto power it up. I changed power outlets and I live in a modern home and I am not aware of any power fluctuations. Is it time to shell out some $$$ for repair or is it better to replace. Although my unit is a few years old, it has barely ever been used. Anyone gotta clue what the issue could be ? Any help is appreciated.

    ReplyDelete
  35. FeatmanNovember 4, 2021 at 7:04 PM

    Will this work with a TSR 5830?
    Is there a protection fuse? May have had a lightning issue.

    ReplyDelete

Subscribe to: Post Comments (Atom)